GPIO & IoT Keywords

Control hardware directly from BASIC dialogs. These keywords work on Raspberry Pi, Orange Pi, and other SBCs running botserver.

Hardware ↔ Keyword Compatibility

Quick Reference by Keyword

Overview

┌────────────────────────────────────────────────────────────────────────┐
│                    GPIO Keyword Architecture                            │
├────────────────────────────────────────────────────────────────────────┤
│                                                                         │
│   BASIC Dialog          botserver            Hardware                  │
│   ┌──────────┐         ┌──────────┐         ┌──────────┐              │
│   │ GPIO SET │────────▶│  sysfs/  │────────▶│   Pin    │              │
│   │ GPIO GET │◀────────│  gpiod   │◀────────│  State   │              │
│   │ I2C READ │◀────────│  i2c-dev │◀────────│  Sensor  │              │
│   │ SPI WRITE│────────▶│  spidev  │────────▶│  Display │              │
│   └──────────┘         └──────────┘         └──────────┘              │
│                                                                         │
└────────────────────────────────────────────────────────────────────────┘

GPIO Keywords

GPIO MODE

Set a GPIO pin as input or output.

' Set pin 17 as output (for LED, relay)
GPIO MODE 17, "OUTPUT"

' Set pin 27 as input (for button, sensor)
GPIO MODE 27, "INPUT"

' Set input with pull-up resistor
GPIO MODE 27, "INPUT_PULLUP"

' Set input with pull-down resistor
GPIO MODE 22, "INPUT_PULLDOWN"

GPIO SET

Set the state of an output pin.

' Turn on LED (HIGH = 3.3V)
GPIO SET 17, HIGH

' Turn off LED (LOW = 0V)
GPIO SET 17, LOW

' Using numeric values (1 = HIGH, 0 = LOW)
GPIO SET 17, 1
GPIO SET 17, 0

GPIO GET

Read the state of an input pin.

' Read button state
GPIO MODE 27, "INPUT_PULLUP"
state = GPIO GET 27

IF state = LOW THEN
    TALK "Button pressed!"
END IF

GPIO PWM

Generate PWM signal for motor speed, LED brightness.

' Set PWM on pin 18, duty cycle 0-100
GPIO PWM 18, 50    ' 50% duty cycle

' Fade LED
FOR brightness = 0 TO 100 STEP 5
    GPIO PWM 18, brightness
    WAIT 0.05
NEXT

' Stop PWM
GPIO PWM 18, 0

GPIO SERVO

Control servo motors (uses hardware PWM).

' Move servo to angle (0-180 degrees)
GPIO SERVO 12, 90    ' Center position
GPIO SERVO 12, 0     ' Left position
GPIO SERVO 12, 180   ' Right position

I2C Keywords

For sensors and displays connected via I2C bus.

I2C SCAN

Scan for connected I2C devices.

' Scan I2C bus 1 (default on Pi)
devices = I2C SCAN 1

FOR EACH addr IN devices
    TALK "Found device at address: " + HEX(addr)
NEXT

I2C READ

Read data from an I2C device.

' Read temperature from sensor at address 0x48
' Register 0x00 contains temperature
temp_raw = I2C READ 0x48, 0x00, 2    ' Read 2 bytes

' Convert to temperature
temperature = temp_raw / 256.0
TALK "Temperature: " + temperature + "°C"

I2C WRITE

Write data to an I2C device.

' Write configuration to sensor
I2C WRITE 0x48, 0x01, 0x60    ' Write 0x60 to register 0x01

' Write multiple bytes
I2C WRITE 0x3C, 0x00, [0xAE, 0xD5, 0x80]    ' OLED init sequence

SPI Keywords

For high-speed communication with displays and sensors.

SPI OPEN

Open SPI device.

' Open SPI device 0, chip select 0
SPI OPEN 0, 0, 1000000    ' 1MHz clock speed

SPI TRANSFER

Send and receive data.

' Send command to display
response = SPI TRANSFER [0x9F]    ' Read ID command

' Send data to display
SPI TRANSFER [0x00, 0xFF, 0x00, 0xFF]    ' Pattern data

SPI CLOSE

Close SPI connection.

SPI CLOSE 0, 0

Sensor Keywords

High-level keywords for common sensors.

READ TEMPERATURE

Read temperature from common sensors (auto-detects DHT11, DHT22, DS18B20, BME280).

temp = READ TEMPERATURE 4    ' GPIO pin 4
TALK "Temperature: " + temp + "°C"

READ HUMIDITY

Read humidity from DHT11/DHT22/BME280.

humidity = READ HUMIDITY 4
TALK "Humidity: " + humidity + "%"

READ DISTANCE

Read distance from ultrasonic sensor (HC-SR04).

' Trigger pin 23, Echo pin 24
distance = READ DISTANCE 23, 24
TALK "Distance: " + distance + " cm"

READ MOTION

Read PIR motion sensor.

GPIO MODE 7, "INPUT"
motion = READ MOTION 7

IF motion THEN
    TALK "Motion detected!"
    GPIO SET 17, HIGH    ' Turn on light
END IF

READ LIGHT

Read light level from photoresistor or light sensor.

light = READ LIGHT 0    ' ADC channel 0 (MCP3008)
TALK "Light level: " + light

Display Keywords

LCD INIT

Initialize character LCD (HD44780).

' I2C LCD at address 0x27, 16 columns, 2 rows
LCD INIT 0x27, 16, 2

LCD PRINT

Print text to LCD.

LCD PRINT "Hello World!"

' Print at specific position (row, column)
LCD PRINT 0, 0, "Line 1"
LCD PRINT 1, 0, "Line 2"

LCD CLEAR

Clear the LCD display.

LCD CLEAR

OLED INIT

Initialize OLED display (SSD1306).

' I2C OLED at address 0x3C, 128x64 pixels
OLED INIT 0x3C, 128, 64

OLED PRINT

Print text to OLED.

OLED PRINT "Hello!"

' With position and size
OLED PRINT 0, 0, "Title", 2    ' Size 2x
OLED PRINT 0, 20, "Subtitle", 1

OLED DRAW

Draw shapes on OLED.

' Draw rectangle
OLED DRAW "rect", 10, 10, 50, 30

' Draw circle
OLED DRAW "circle", 64, 32, 20

' Draw line
OLED DRAW "line", 0, 0, 127, 63

OLED CLEAR

Clear the OLED display.

OLED CLEAR

Relay & Actuator Keywords

RELAY SET

Control relay module.

' Turn on relay 1 (pin 17)
RELAY SET 17, ON

' Turn off relay
RELAY SET 17, OFF

' Toggle relay
state = GPIO GET 17
RELAY SET 17, NOT state

BUZZER

Control buzzer for alerts.

' Beep for 0.5 seconds
BUZZER 18, 0.5

' Play tone (frequency, duration)
BUZZER 18, 1000, 0.2    ' 1000Hz for 0.2 seconds

' Play melody
BUZZER 18, 262, 0.25    ' C4
BUZZER 18, 294, 0.25    ' D4
BUZZER 18, 330, 0.25    ' E4

Complete Examples

Smart Doorbell

' Smart doorbell with camera and notification
' Hardware: Button on GPIO 27, Buzzer on GPIO 18, LED on GPIO 17

GPIO MODE 27, "INPUT_PULLUP"
GPIO MODE 18, "OUTPUT"
GPIO MODE 17, "OUTPUT"

TALK "Doorbell system ready"
LCD PRINT "Ring the bell"

mainLoop:
    button = GPIO GET 27
    
    IF button = LOW THEN
        ' Button pressed
        GPIO SET 17, HIGH        ' LED on
        BUZZER 18, 1000, 0.5     ' Ring buzzer
        
        ' Take photo (if camera connected)
        photo = CAPTURE PHOTO
        
        ' Send notification
        SEND MAIL "owner@home.com", "Doorbell", "Someone at the door!", photo
        
        LCD PRINT "Visitor!"
        WAIT 2
        LCD PRINT "Ring the bell"
        GPIO SET 17, LOW         ' LED off
    END IF
    
    WAIT 0.1
GOTO mainLoop

Temperature Monitor

' Temperature and humidity monitor with OLED display
' Hardware: DHT22 on GPIO 4, OLED on I2C 0x3C

OLED INIT 0x3C, 128, 64

mainLoop:
    temp = READ TEMPERATURE 4
    humidity = READ HUMIDITY 4
    
    OLED CLEAR
    OLED PRINT 0, 0, "Temperature:", 1
    OLED PRINT 0, 15, temp + " C", 2
    OLED PRINT 0, 40, "Humidity:", 1
    OLED PRINT 0, 55, humidity + " %", 2
    
    ' Alert if too hot
    IF temp > 30 THEN
        BUZZER 18, 2000, 0.1
        SEND MAIL "admin@home.com", "Alert", "Temperature high: " + temp + "C"
    END IF
    
    WAIT 5    ' Update every 5 seconds
GOTO mainLoop

Light Automation

' Automatic light control based on motion and ambient light
' Hardware: PIR on GPIO 7, Light sensor on ADC0, Relay on GPIO 17

GPIO MODE 7, "INPUT"
GPIO MODE 17, "OUTPUT"

threshold = 500    ' Light threshold
timeout = 30       ' Seconds to keep light on

lastMotion = 0

mainLoop:
    motion = READ MOTION 7
    light = READ LIGHT 0
    
    IF motion AND light < threshold THEN
        ' Dark and motion detected
        RELAY SET 17, ON
        lastMotion = NOW
        LCD PRINT "Light ON"
    END IF
    
    ' Turn off after timeout
    IF NOW - lastMotion > timeout THEN
        RELAY SET 17, OFF
        LCD PRINT "Light OFF"
    END IF
    
    WAIT 0.5
GOTO mainLoop

Voice-Controlled Lights

' Voice control for home automation
' Ask the AI to control lights

TALK "What would you like me to do?"
command = HEAR

' Use LLM to understand command
intent = LLM "Extract intent from: '" + command + "'. Return JSON: {action: on/off, room: string}"
intent = JSON PARSE intent

SELECT CASE intent.room
    CASE "living room"
        RELAY SET 17, intent.action = "on"
    CASE "bedroom"
        RELAY SET 18, intent.action = "on"
    CASE "kitchen"
        RELAY SET 27, intent.action = "on"
    CASE "all"
        RELAY SET 17, intent.action = "on"
        RELAY SET 18, intent.action = "on"
        RELAY SET 27, intent.action = "on"
END SELECT

TALK "Done! " + intent.room + " light is now " + intent.action

Pin Reference

Raspberry Pi GPIO

Orange Pi GPIO

Similar pinout, but check your specific model. Orange Pi 5 uses different GPIO numbering.

Troubleshooting

Permission Denied

# Add user to gpio group
sudo usermod -a -G gpio $USER
sudo usermod -a -G i2c $USER
sudo usermod -a -G spi $USER

# Or run botserver with elevated privileges
sudo systemctl edit botserver
# Add: User=root

I2C Not Working

# Enable I2C
sudo raspi-config  # Interface Options → I2C

# Check if device detected
i2cdetect -y 1

GPIO Busy

# Check what's using the GPIO
cat /sys/kernel/debug/gpio

# Release GPIO
echo 17 > /sys/class/gpio/unexport